![]() ![]() Parts Unlimited offers a 3-set of clutch shoes for $50 and they are supposed to be an OEM equivalent part. Lastly, if you know of a sourch for the clutch drum (the area the clutch shoes rub on) please advise. ![]() Also, I recently started another thread about my xr200 cam install, I'll finish that one after I get the new clutch sorted out. I'll be adding my findings and impressions of the Barnett clutches. If you have any information to add to this thread that is of substance and may help people in the future, please add it. So, I have my new clutch discs in hand and tomorrow/soon I plan to dive into the side of my case and she what it looks like. 1986 Honda Rebel 450 Honda, Fresh: Carb Clean Plugs Pet Cock Oil Change Fuel Flush New Pipes Consignment unit Engine and transmission Displacement: 447.00 ccm (27.28 cubic inches) Engine type: Twin Stroke: 4 Power: 38.00 HP (27.7 rkW)) 8000 RPM Compression: 9.3:1 Bore x stroke: 75.0 x 50.6 mm (3. If it looks like there are any grooves machined into the inside of your drum than it's off to see Honda. If it has ridges it will need to be replaced to the tune of $140-ish from Honda with a 2-week wait. It is supposed to be completely smooth and not have any ridges in it. ![]() She advised me to take the shoes out and inspect the drum. This runs and rides just needs some TLC and fine tuning. I believe everything else to be original equipment. She also said that if the shoes are slipping that there is a good chance they have damaged the drum that they grab. It has new carb, rear wheel bearings, recoil rope, sprocket, axel and tires. I passed on the shoes, but did learn some. Well, she tried to sell me Honda clutch shoes for $60 a piece (remember we need three). Caltric O-Ring Drive Chain Compatible with Honda Atc185S Atc-185S 185S 1981-1983 Green. Once the shoes start to slip then, the discs will glaze over requiring all parts to be replaced. I learned that the shoes are probably slipping and that this is a common problem. While I was at Winner's Cycle in BTR I talked to one of the salespersons there. 1983 honda 200x 185 motor, Uni air filter, bassani exhaust, itp rims. Well, today I bought four Barnett clutch discs for my 200s. So far, I've tried to adjust the slack (necessary as clutch shoes wear) and that hasn't helped much. ![]() I will be cleaning the frame and repainting it too.Okay, my clutch is slipping and I'm not being able to transfer all of my bike's power to the ground. NICECNC 1Pair 30MM Upright Fork Shock Boots Gators Boot Black Rubber Compatible with Honda ATC 185S ATC200 200M 200S 1983-1984 and More with Similar-Sized Forks. What kind of paint are you using on those rims? they look great! Right now I have the motor out of the frame getting it ready for the head. QUALITY Top End Engine Motor Gasket Kit Set FOR THE 1980-1983 Honda ATC 185 185S 200 Three-wheel ATVs. I had the same problem with 3 sets of tires leaking.this is what i've done and it works perfect each time.take the rims of the tires,split the rims in half.take a wire wheel on a grinder(4 1/2 inch grinder with wire wheel fits just right down inside the rim if you want to go ahead and paint the outside of the rims while they are broke down)clean the whole inside rim and pay close attention where the halves meet and where the bead is.spray some the whole inside rim with etch primer so that it want rust later on.take one rim and set it back down in the tire and silicon wher the halves meet,set the othe rim down on top of the first half inside the tire,put your bolts in to make sure they are all lined up but dont tighten anything down yet,let the silicon cure or dry for about 20-30 mins depending on the temp.after it has dried snug the bolts and inflat and your ready to go.couple pictures of the last rims i've done. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |